Control-company 3655 MICRO ANEMOMETER/THERMOMETER User Manual download pdf

SPECIFICATIONS

Air Flow—

Range: 0.0 to 30.0 m/s (meters per second)

Resolution: 0.1

Range: 0.0 to 108.0 km/h (kilometers per hour)

Resolution: 0.1

Range: 0.0 to 98.0 fps (feet per second)

Resolution: 0.1

Range: 0.0 to 67.0 mph (miles per hour)

Resolution: 0.1

Range: 0.0 to 58.0 knots (nautical miles/hour)

Resolution: 0.1

Temperature—

Range: -4.0 to 176.0 °F / -20.0 to 80.0 °C

Resolution: 0.1°

Update Rate: ½ second

Battery: 1 each CR2032 (3V Lithium)

PRESSING THE ON/OFF BUTTON

The meter is designed so that all features may be

accessed using a single button (ON/OFF).

Quick Press (QP) – A quick press (press and

release) of the ON/OFF button will change the

display mode.

Slow Press (SP) – A slow press (slowly press and

hold for X seconds) will access user selectable

features such as units of measure.

DISPLAY MODES

The meter may be set to the following display modes:

Anemometer and Maximum Air Speed (An/Max)

(Anemometer reading shown in the upper display, maximum air

speed achieved shown in the lower display)

Anemometer and Temperature (An/Temp)

(Anemometer reading shown in the upper display, temperature

shown in the lower display)

Temperature is indicated by °F or °C appearing on the display.

Anemometer and Wind Chill (An/WC)

(Anemometer reading shown in the upper display, wind chill

temperature shown in the lower display)

Wind chill is indicated by

appearing on the display (°F/°C

will not appear).

To change the display mode, press (QP) the

ON/OFF button. With each press (QP) of the

ON/OFF button, the display will cycle through the

available display modes (An/Max→An/Temp→

An/WC→An/Max...).

OPERATION

1. Press (QP) the ON/OFF button to turn the

meter on.

2. Select the desired display mode (see the

“Display Modes” section).

3. Take the desired measurements.

If no button is pressed, after one (1) minute, the

meter will turn off automatically to preserve battery

life (see the “Automatic Shutoff” section).

TEMPERATURE MEASUREMENT

The temperature sensor is located at

the back of the unit (see illustration).

To insure accurate temperature

measurements, make certain that

the temperature sensor is not

blocked and that it is not in contact

with the hand when being held

during measurement.

SELECTING °F OR °C

(Temperature/Wind Chill)

1. Place the meter in the Anemometer/

Temperature display mode (see the “Display

Modes” section).

2. Press (SP) and hold the ON/OFF button for

approximately ﬁ ve (5) seconds, the temperature

reading will switch to the opposite unit of

measure. If the meter had been displaying °F,

it will now display °C, and vice-versa.

The unit of measure selected will be the default

unit of measure for both temperature and wind chill

until changed.

TRACEABLE

MICRO

ANEMOMETER/

THERMOMETER

INSTRUCTIONS

SELECTING ANEMOMETER UNIT OF MEASURE

1. Place the meter in the Anemometer/Maximum

Air Speed display mode (see the “Display

Modes” section).

2. Press (SP) and hold the ON/OFF button, after

approximately ﬁ ve (5) seconds, the display

will cycle through the available units of measure

(m/s→km/h→knots→fps→mph→m/s...).

Once the desired unit of measure appears,

release the ON/OFF button.

AUTOMATIC SHUTOFF

If no button has been pressed for one (1) minute,

the Automatic Shutoff feature will turn the meter off

to preserve battery life.

To prevent the meter from automatically turning

off during extended measurement, press (SP) and

hold the ON/OFF button for 1 second prior to the

end of the 1 minute Automatic Shutoff period.

BACKLIGHT

During measurement in any display mode, press

(SP) and hold the ON/OFF button for 2 seconds

to activate the display backlight. The backlight will

illuminate the display for 3 seconds.

If, within 5 seconds of turning on the backlight,

the ON/OFF button is pressed (SP) and held for 2

seconds, the backlight will illuminate the display for

ﬁ fteen 15 seconds.

Frequent use of the backlight will greatly reduce

the battery life.

ALL OPERATION DIFFICULTIES

If this meter does not function properly for any

reason, replace the battery with a new, high quality

battery (see the “Battery Replacement” section).

Low battery power can occasionally cause an

number of “apparent” operational difﬁ culties.

Replacing the battery with a new fresh battery will

solve most difﬁ culties.

BATTERY REPLACEMENT

An erratic display, faint display, or no display are

all indicators that the battery needs replacement.

Remove the four screws located on the back of

the unit. Remove the back of the unit. Remove

the exhausted battery and replace it with a new

CR2032 lithium battery. Make certain to insert

the new battery with the “+” side up. Replace the

back cover making certain that the temperature

sensor is lined up properly with the rubber gasket.

Replace the four screws and tighten securely.

WARRANTY, SERVICE, OR RECALIBRATION

For warranty, service, or recalibration, contact:

CONTROL COMPANY

4455 Rex Road

Friendswood, Texas 77546 USA

Ph. 281 482-1714 • Fax 281 482-9448

E-mail [email protected] • www.control3.com

Control Company is ISO 9001 Quality-Certiﬁ ed by DNV and

ISO 17025 accredited as a Calibration Laboratory by A2LA.

Control Company Cat. No. 3655

Traceable

is a registered trademark of Control Company.

2009 Control Company. 92-3655-00 Rev. 0 081909

Summary of Contents

Page 1 - INSTRUCTIONS

SPECIFICATIONSAir Flow—Range: 0.0 to 30.0 m/s (meters per second)Resolution: 0.1Range: 0.0 to 108.0 km/h (kilometers per hour)Resolution: 0.1R

Comments to this Manuals

No comments

Control-company 3655 MICRO ANEMOMETER/THERMOMETER User Manual

Browse online or download User Manual for Measuring instruments Control-company 3655 MICRO ANEMOMETER/THERMOMETER. Control Company 3655 MICRO ANEMOMETER/THERMOMETER User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Measuring instruments Control-company 3655 MICRO ANEMOMETER/THERMOMETER